---
title: "Sennheiser EW-DX"
url: "https://showcaller.ai/integrations/sennheiser-ew-dx/"
type: "integration"
published: "2026-03-11T20:50:57+00:00"
modified: "2026-11-06T19:33:05+00:00"
author: "admin"
---

Sennheiser EW-DX remote control from Showcaller AI lets you monitor and control receivers by voice or chat. It works over your local network with Evolution Wireless Digital (EW-DX) receivers. For example, mute a receiver output before a presenter walks off with a live mic. Then bring it back for the next session. You can also trim a channel’s gain. Or give each channel the presenter’s name, so everyone knows who is on which mic.

Showcaller connects to each receiver through the Bridge App on your show network. It reads each channel’s name, mute state, gain and output level. It also reads the transmitter linked to each channel. That means its type, name and firmware, plus its mute and lock state. When you need a new frequency, Showcaller can read or change a channel’s operating frequency in kHz. However, it confirms a retune with you before it sends it.

Showcaller reads every mute, frequency and channel name change back from the receiver before it reports it done.

What Sennheiser EW-DX remote control cannot do matters on wireless, so here it is plainly. The EW-DX network interface does not offer RF scans or automatic frequency setup. It also has no squelch control, no transmitter mute or lock changes and no device renaming. Battery and RF level readings are missing too, so Showcaller does not offer any of these. Instead, mute happens at the receiver output. Showcaller reads the transmitter lock but does not change it.

Showcaller supports the EW-DX EM 2, EM 2 Dante and [EM 4 Dante](/integrations/sennheiser-ew-dx/sennheiser-ew-dx-em-4-dante/) receivers on firmware 4.x or later. Before you start, switch on third-party network access in each receiver. The FAQ below explains how. For the receiver itself, see [Sennheiser’s EW-DX EM 2 page](https://www.sennheiser.com/en-us/catalog/products/wireless-systems/ew-dx-em-2).

## Questions about Sennheiser EW-DX remote control

### Which EW-DX receivers are supported?

Showcaller supports the EW-DX EM 2, EM 2 Dante and EM 4 Dante receivers. They need firmware 4.x or later.

### What do I need to set up on the receiver?

Third-party network access (SSCv2) is off by default on EW-DX receivers. So first, turn it on in Sennheiser Control Cockpit or in the receiver’s own web interface. You find it under the network or third-party access settings. Then set a password. Showcaller needs the receiver’s IP address and that password. The username is always “api”. Also, the Showcaller Bridge App must run on a computer on the same network.

### Which plan includes which Tool Functions?

Starter includes Device Diagnostics and Mute Control. That covers receiver identity, channel and transmitter status, and receiver output mute. Pro adds Audio Gain Control and Channel & Frequency Management, such as channel names and frequencies. It also adds reading the transmitter lock state. There are no Enterprise-only functions for EW-DX. Each plan includes every Tool Function of the plans below it. See [pricing](/pricing/) for the plans themselves.

### Can Showcaller run an RF scan or check battery levels?

No. The EW-DX network interface has no RF scan or automatic frequency setup. So Showcaller does not run an RF scan on EW-DX. The interface also has no battery or RF level readings, so Showcaller cannot offer them. For battery monitoring over the network, see the [Shure Wireless integration](/integrations/shure-wireless/) for ULX-D, QLX-D and SLX-D.

### Can Showcaller mute the transmitter itself?

No. The EW-DX network interface does not offer transmitter mute. Instead, Showcaller mutes the receiver output.
