Shure SLXD4 single-channel receiver
Showcaller AI reads and sets a Shure SLXD4 by voice or chat. It covers transmitter battery, output gain, the channel name and frequency. Remote mute is not available on SLX-D.

Overview
The Shure SLXD4 single-channel receiver with Showcaller
The Shure SLXD4 is an SLX-D digital receiver for one wireless channel. It has an XLR output, a 1/4″ output and one Ethernet port. Showcaller AI connects to the Shure SLXD4 over your show network through the Bridge App. Then it answers the questions an A2 asks all show long, by voice or chat. For example: How long is left on the lectern pack? What gain is it at? Which Group and Channel is it on? The Shure wireless integration page lists every function.
Allow control on the Shure SLXD4 first
SLX-D blocks third-party command strings by default. So before Showcaller can connect, allow it on the receiver. Go to Advanced Settings, then Controller Access. After that, Showcaller reaches the receiver on TCP port 2202. It reads the full channel status in one request.
Battery, gain and name
Showcaller reads the transmitter battery as bars, from 0 to 5, and the runtime in minutes. However, SLX-D does not report battery charge or health percentages. Those come with ULX-D and QLX-D only. Battery functions are in every plan. From the Pro plan, Showcaller reads and sets the output gain in 1 dB steps. The range is -18 to +42 dB, the receiver’s own range. It also sets the channel name, from 1 to 8 characters, such as “Lectern”.
Frequencies and what SLX-D lacks
With Enterprise, Showcaller reads the frequency in kHz and the Group and Channel. It can also move the channel to a new frequency or Group/Channel. First, though, it asks you before it retunes. In addition, it can flash the receiver’s front panel to find it in a rack. On the other hand, SLX-D has no remote audio mute, so Showcaller cannot mute the channel. Mute it at your console instead. Also, Shure’s SLX-D guide lists no AES-256 encryption, unlike QLX-D and ULX-D. Showcaller does not scan the spectrum or lock transmitters. For full specs, see Shure’s SLX-D system guide.
What you can do
Run the Shure SLXD4 single-channel receiver by voice or chat
Battery bars and runtime
Battery bars and runtime in minutes for the channel. No charge or health percentage on SLX-D. Starter.
Firmware and status
Read the firmware version and the status of the channel in one request. Starter.
Gain in 1 dB steps
Read or set the output gain from -18 to +42 dB. Pro.
Frequency and Group/Channel
Read or change the frequency or Group/Channel. Showcaller asks before it retunes. Enterprise.
Find it in the rack
Flash the SLXD4's front panel, then stop the flash once it is found. Enterprise.
Specifications
Shure SLXD4 single-channel receiver at a glance
RF
- Channels
- 1 receiver channel
- Tuning bandwidth
- 44 MHz, region dependent; 32 available channels per band
- Compatible systems
- Up to 10 systems per 6 MHz TV channel; 12 per 8 MHz
- RF tuning step
- 25 kHz, varies by region (JB band: 125 kHz)
- Working range
- 100 m (328 ft); depends on RF conditions
- Diversity
- Digital predictive switching diversity
Audio
- Gain adjustment range
- -18 to +42 dB in 1 dB steps
- Audio outputs
- XLR balanced, mic/line switchable (30 dB pad); 1/4" (6.35 mm) balanced
- Latency
- 3.2 ms
- Dynamic range
- 118 dB at 1% THD, A-weighted
- High-pass filter
- 150 Hz at -12 dB/octave, off by default
Control & network
- Network interface
- Single-port Ethernet 10/100 Mbps; DHCP or manual IP
- Third-party control
- AMX/Crestron control over Ethernet TCP/IP, port 2202; blocked by default, allowed in Advanced Settings > Controller Access
Physical
- Dimensions and weight
- 42 x 197 x 152 mm (H x W x D); 816 g without antennas
- Power
- 15 V DC at 600 mA from an external supply
Specifications from the manufacturer. Check the product page for the current details.
Connection
Connecting the Shure SLXD4 single-channel receiver
- Control protocol
- Shure network control over TCP/IP on port 2202, through the Showcaller Bridge App. No username or password.
- Allow control first
- SLX-D blocks command strings by default. On the receiver, open Advanced Settings > Controller Access and allow third-party control.
- What Showcaller needs
- The receiver's IP address, shown on the front panel in the Network menu, and the model SLXD4 (Single Channel).
- Network
- Connect the receiver's Ethernet port to the same network as the Bridge App.
- First check
- Showcaller reads the firmware version to check it can reach the receiver, then reads the status of the channel.
Tool Functions
Everything Showcaller can do with Shure Wireless
The Shure SLXD4 single-channel receiver uses the Shure Wireless integration. Each group shows the plan it is included from.
FAQ
Questions about the Shure SLXD4 single-channel receiver
Can Showcaller mute a channel on a Shure SLXD4?
No. SLX-D receivers have no remote audio mute, so mute control works on ULX-D only. Mute the channel at your console instead.
Why can Showcaller not connect to my SLX-D receiver?
SLX-D blocks third-party command strings by default. Allow them in Advanced Settings > Controller Access. Then check the IP address and that the receiver is on the Bridge App's network.
How much battery is left on an SLX-D transmitter?
Ask Showcaller for the battery bars or the runtime in minutes. Charge and health percentages are not available on SLX-D.
Can Showcaller change the frequency of a SLXD4?
Yes, with the Enterprise plan. It sets a new frequency or Group/Channel and asks you before it retunes. It does not run an RF scan.
What is the difference between the SLXD4 and SLXD4D in Showcaller?
The Tool Functions are the same. The SLXD4 has one channel and the SLXD4D two. Pick the matching model when you connect so Showcaller addresses the right channels.
Same integration
Other Shure Wireless models
QLXD4 (Single Channel)Model page
SLXD4D (Dual Channel)Model page
ULXD4 (Single Channel)Model page
ULXD4D (Dual Channel)Model page
ULXD4Q (Quad Channel)Model page


