Skip to content
Skip to content

Shure SLXD4D dual-channel receiver

Showcaller AI reads and sets both channels of a Shure SLXD4D by voice or chat. It covers transmitter battery, output gain, channel names and frequency. Remote mute is not available on SLX-D.

Shure SLXD4D dual-channel receiver

Overview

The Shure SLXD4D dual-channel receiver with Showcaller

The Shure SLXD4D puts two SLX-D digital receivers in one chassis. Each channel pairs with its own bodypack or handheld. Showcaller AI connects to the Shure SLXD4D over your show network through the Bridge App. Then it answers the questions an A2 asks all show long, for channel 1 or channel 2. For example: How long is left on the handheld on channel 2? What gain is channel 1 at? The Shure wireless integration page lists every function.

Allow control on the Shure SLXD4D first

SLX-D blocks third-party command strings by default. So before Showcaller can connect, allow it on the receiver. Go to Advanced Settings, then Controller Access. After that, Showcaller reaches the receiver on TCP port 2202. It reads the status of both channels in one request.

Battery, gain and names

For each channel, Showcaller reads the transmitter battery as bars, from 0 to 5, and the runtime in minutes. However, SLX-D does not report battery charge or health percentages. Those come with ULX-D and QLX-D only. Battery functions are in every plan. From the Pro plan, Showcaller reads and sets each channel’s gain in 1 dB steps. The range is -18 to +42 dB, the receiver’s own range. It also names each channel with 1 to 8 characters, such as “Host” and “Guest”.

Frequencies and what SLX-D lacks

With Enterprise, Showcaller reads each channel’s frequency in kHz and its Group and Channel. It can move a channel to a new frequency or Group/Channel. First, though, it asks you before it retunes. It can also flash the receiver’s front panel to find it in a rack. On the other hand, SLX-D has no remote audio mute, so Showcaller cannot mute a channel. Mute it at your console instead. Also, Shure’s SLX-D guide lists no AES-256 encryption, unlike QLX-D and ULX-D. Showcaller does not scan the spectrum or lock transmitters. For full specs, see Shure’s SLX-D system guide.

What you can do

Run the Shure SLXD4D dual-channel receiver by voice or chat

  • Battery bars and runtime

    Battery bars and runtime in minutes for each channel. No charge or health percentage on SLX-D. Starter.

  • Firmware and status

    Read the firmware version and the status of both channels in one request. Starter.

  • Gain in 1 dB steps

    Read or set each channel's output gain from -18 to +42 dB. Pro.

  • Frequency and Group/Channel

    Read or change a channel's frequency or Group/Channel. Showcaller asks before it retunes. Enterprise.

  • Find it in the rack

    Flash the SLXD4D's front panel, then stop the flash once it is found. Enterprise.

Specifications

Shure SLXD4D dual-channel receiver at a glance

RF

Channels
2 receiver channels in one chassis
Tuning bandwidth
44 MHz, region dependent; 32 available channels per band
Compatible systems
Up to 10 systems per 6 MHz TV channel; 12 per 8 MHz
RF tuning step
25 kHz, varies by region (JB band: 125 kHz)
Working range
100 m (328 ft); depends on RF conditions
Diversity
Digital predictive switching diversity

Audio

Gain adjustment range
-18 to +42 dB in 1 dB steps
Audio outputs
XLR balanced, mic/line switchable (30 dB pad); 1/4" (6.35 mm) balanced
Latency
3.2 ms
Dynamic range
118 dB at 1% THD, A-weighted
High-pass filter
150 Hz at -12 dB/octave, off by default

Control & network

Network interface
Single-port Ethernet 10/100 Mbps; DHCP or manual IP
Third-party control
AMX/Crestron control over Ethernet TCP/IP, port 2202; blocked by default, allowed in Advanced Settings > Controller Access

Physical

Dimensions and weight
42 x 393 x 152 mm (H x W x D); 1451 g without antennas
Power
15 V DC at 600 mA from an external supply

Specifications from the manufacturer. Check the product page for the current details.

Connection

Connecting the Shure SLXD4D dual-channel receiver

Control protocol
Shure network control over TCP/IP on port 2202, through the Showcaller Bridge App. No username or password.
Allow control first
SLX-D blocks command strings by default. On the receiver, open Advanced Settings > Controller Access and allow third-party control.
What Showcaller needs
The receiver's IP address, shown on the front panel in the Network menu, and the model SLXD4D (Dual Channel).
Network
Connect the receiver's Ethernet port to the same network as the Bridge App.
First check
Showcaller reads the firmware version to check it can reach the receiver, then reads the status of both channels.

FAQ

Questions about the Shure SLXD4D dual-channel receiver

Can Showcaller mute a channel on a Shure SLXD4D?

No. SLX-D receivers have no remote audio mute, so mute control works on ULX-D only. Mute the channel at your console instead.

Why can Showcaller not connect to my SLX-D receiver?

SLX-D blocks third-party command strings by default. Allow them in Advanced Settings > Controller Access. Then check the IP address and that the receiver is on the Bridge App's network.

How much battery is left on an SLX-D transmitter?

Ask Showcaller for the battery bars or the runtime in minutes. Charge and health percentages are not available on SLX-D.

Can Showcaller change the frequency of a SLXD4D?

Yes, with the Enterprise plan. It sets a new frequency or Group/Channel and asks you before it retunes. It does not run an RF scan.

What is the difference between the SLXD4D and SLXD4 in Showcaller?

The Tool Functions are the same. The SLXD4D has two channels and the SLXD4 one. Pick the matching model when you connect so Showcaller addresses the right channels.

Same integration

Other Shure Wireless models