Shure ULXD4Q quad-channel receiver
Showcaller AI reads and sets all four channels of a Shure ULXD4Q by voice or chat. It covers transmitter battery, output mute and gain, plus channel names and frequency.

Overview
The Shure ULXD4Q quad-channel receiver with Showcaller
The Shure ULXD4Q puts four ULX-D digital receivers in one rack unit. Each channel has its own gain control, meters and XLR output. In addition, the unit has Dante on two Ethernet ports and an internal power supply. Showcaller AI connects to the Shure ULXD4Q over your show network through the Bridge App. Then it answers the questions an A2 asks all show long, for any of the four channels. For example: Which pack is lowest on battery? What gain is channel 3 at? Is the panel mic on channel 4 muted? The Shure wireless integration page lists every function.
Battery on all four channels of the Shure ULXD4Q
Showcaller reads the status of all four channels in one request. That makes a quick battery round before the next session easy. For each channel, it reads the transmitter battery as bars, from 0 to 5. With Shure rechargeable batteries, it also reads the runtime in minutes. It reads their charge and health percentages, too. Battery and mute functions are in every plan.
Remote mute, gain and names
Remote mute is the main difference between ULX-D and the QLX-D and SLX-D receivers. On the ULXD4Q, Showcaller mutes and unmutes each channel’s output. Meanwhile, the RF link to the transmitter stays up. However, Shure notes that a power cycle unmutes the outputs. So ask Showcaller for the mute state after a restart. From the Pro plan, Showcaller reads and sets each channel’s gain in 1 dB steps, from -18 to +42 dB. It also names each channel with 1 to 8 characters, such as “PANEL1” to “PANEL4”.
Frequencies on Enterprise
With Enterprise, Showcaller reads each channel’s frequency in kHz and its Group and Channel. It can move a channel to a new frequency or Group/Channel. First, though, it asks you before it retunes. Showcaller can also flash the front-panel LEDs to find the unit in a rack. Note that the ULXD4Q’s own features stay on the receiver. For example, audio summing turns the unit into a four-channel mixer. Likewise, frequency diversity, High Density mode and Dante routing are set on the receiver or in Wireless Workbench. Showcaller does not scan the spectrum or lock transmitters. For full specs, see Shure’s ULXD4Q product page.
What you can do
Run the Shure ULXD4Q quad-channel receiver by voice or chat
Battery on four channels
Battery bars for each channel, plus runtime, charge and health percentage for Shure rechargeables. Starter.
Remote output mute
Mute or unmute any of the four channels without dropping the RF link, and read the mute state. ULX-D only. Starter.
Gain in 1 dB steps
Read or set each channel's output gain from -18 to +42 dB. Pro.
Frequency and Group/Channel
Read or change a channel's frequency or Group/Channel. Showcaller asks before it retunes. Enterprise.
Find it in the rack
Flash the ULXD4Q's front-panel LEDs, then stop the flash once it is found. Enterprise.
Specifications
Shure ULXD4Q quad-channel receiver at a glance
RF
- Channels
- 4 independent receivers in one 1RU metal chassis
- Tuning range
- Up to 166 MHz per band, region dependent; bands listed on shure.com (US): G57, V50, X52
- RF tuning step
- 25 kHz, varies by region
- Working range
- 100 m (330 ft); depends on RF conditions
- Diversity
- Digital predictive switching diversity; bodypack frequency diversity
- RF cascade
- BNC cascade output for one additional receiver in the same band
Audio
- Gain adjustment range
- -18 to +42 dB in 1 dB steps, plus Mute
- Audio outputs
- 4 XLR, balanced, mic/line switchable (30 dB pad); audio summing routes channels to combinations of outputs
- Latency
- < 2.9 ms
- Dynamic range
- > 120 dB XLR analog, 130 dB Dante (A-weighted, system gain +10)
Control & network
- Network interface
- Dual-port Ethernet 10/100 Mbps, 1 Gbps, with Dante digital audio; DHCP or manual IP
- Third-party control
- AMX/Crestron control over Ethernet TCP/IP, port 2202
- Encryption
- AES-256
Physical
- Dimensions and weight
- 44 x 482 x 274 mm (H x W x D); 3.45 kg without antennas
- Power
- Internal supply, 100 to 240 V AC, 50-60 Hz, 0.32 A max.
Specifications from the manufacturer. Check the product page for the current details.
Connection
Connecting the Shure ULXD4Q quad-channel receiver
- Control protocol
- Shure network control over TCP/IP on port 2202, through the Showcaller Bridge App. No username or password.
- What Showcaller needs
- The receiver's IP address, shown on the front panel in the Network menu, and the model ULXD4Q (Quad Channel).
- Network
- Connect the Primary Ethernet port to the same network as the Bridge App. Shure Control is on the Primary port in all three Dante modes (Switched, Redundant Audio and Split).
- Firmware
- Showcaller reads the receiver's firmware version when it connects. On newer firmware, third-party network control may need to be switched on in Wireless Workbench or the receiver's web interface.
- First check
- Showcaller reads the firmware version to check it can reach the receiver, then reads the status of all four channels.
Tool Functions
Everything Showcaller can do with Shure Wireless
The Shure ULXD4Q quad-channel receiver uses the Shure Wireless integration. Each group shows the plan it is included from.
FAQ
Questions about the Shure ULXD4Q quad-channel receiver
Can Showcaller mute a channel on a Shure ULXD4Q?
Yes, in every plan. Showcaller mutes and unmutes each channel's audio output without dropping the RF link, and reads the mute state. Shure notes that a power cycle unmutes the receiver outputs.
Can I check the battery of all four transmitters at once?
Yes. Showcaller reads the status of all four channels in one request. Then ask for the bars or runtime of any channel. Runtime, charge and health need Shure rechargeable batteries.
Does Showcaller control Dante or audio summing on the ULXD4Q?
No. Set Dante routing, audio summing and frequency diversity on the receiver, in Wireless Workbench or in Dante Controller. Showcaller reads and sets each channel's gain, mute, name and frequency.
What is the difference between the ULXD4Q, ULXD4D and ULXD4 in Showcaller?
The Tool Functions are the same on all ULX-D receivers. The ULXD4Q has four channels, the ULXD4D two and the ULXD4 one. Pick the matching model when you connect so Showcaller addresses the right channels.
Can Showcaller run an RF scan on the ULXD4Q?
No. Showcaller reads and sets frequencies and Group/Channel assignments, but it does not scan the RF spectrum. Use the receiver's scan or Wireless Workbench for that.
Same integration
Other Shure Wireless models
QLXD4 (Single Channel)Model page
SLXD4 (Single Channel)Model page
SLXD4D (Dual Channel)Model page
ULXD4 (Single Channel)Model page
ULXD4D (Dual Channel)Model page



