Shure ULXD4 single-channel receiver
Showcaller AI reads and sets a Shure ULXD4 by voice or chat. It covers transmitter battery, remote output mute and gain, plus the channel name and frequency.

Overview
The Shure ULXD4 single-channel receiver with Showcaller
The Shure ULXD4 is a half-rack ULX-D digital receiver for one wireless channel. It has an XLR output, a 1/4″ output and one Ethernet port. Showcaller AI connects to the Shure ULXD4 over your show network through the Bridge App. Then it answers the questions an A2 asks all show long, by voice or chat. For example: How long is left on the lectern pack? Is the podium mic muted? What gain is it at? The Shure wireless integration page lists every function.
Battery and status on the Shure ULXD4
Showcaller reads the full channel status in one request. It reads the transmitter battery as bars, from 0 to 5. With Shure rechargeable batteries, it also reads the runtime in minutes. In addition, it reads the charge and health percentages of those batteries. Shure rates ULX-D rechargeable metering as accurate to within 15 minutes. With AA batteries, however, Showcaller reads the bars only. Battery and mute functions are in every plan.
Remote mute and gain
ULX-D is the only Shure family in this integration with remote audio mute. So on the ULXD4, Showcaller mutes and unmutes the audio output. Meanwhile, the RF link to the transmitter stays up. Shure notes that a power cycle unmutes the output. Therefore, ask Showcaller for the mute state after a restart. From the Pro plan, Showcaller reads and sets the output gain in 1 dB steps. The range is -18 to +42 dB, the receiver’s own range. It also sets the channel name, from 1 to 8 characters, so “LECTERN” shows on the front panel.
Frequencies, and how the Shure ULXD4 differs
With Enterprise, Showcaller reads the channel’s frequency in kHz and its Group and Channel. It can also move the channel to a new frequency or Group/Channel. First, though, it asks you before it retunes. Showcaller can also flash the front-panel LEDs to find the unit in a rack. Unlike the ULXD4D and ULXD4Q, the ULXD4 has no Dante output and no internal power supply. Instead, it runs from an external 15 V DC supply. AES-256 encryption is still available, and you set it on the receiver. Finally, Showcaller does not scan the spectrum or lock transmitters. For full specs, see Shure’s ULXD4 product page.
What you can do
Run the Shure ULXD4 single-channel receiver by voice or chat
Battery runtime and health
Battery bars on any transmitter. With Shure rechargeables, also runtime in minutes, charge and health percentage. Starter.
Remote output mute
Mute or unmute the output without dropping the RF link, and read the mute state. ULX-D only. Starter.
Gain in 1 dB steps
Read or set the output gain from -18 to +42 dB. Pro.
Frequency and Group/Channel
Read or change the frequency or Group/Channel. Showcaller asks before it retunes. Enterprise.
Find it in the rack
Flash the ULXD4's front-panel LEDs, then stop the flash once it is found. Enterprise.
Specifications
Shure ULXD4 single-channel receiver at a glance
RF
- Channels
- 1 receiver channel in a half-rack steel chassis
- Tuning range
- Up to 64 MHz, region dependent; bands listed on shure.com (US): G50, H50, J50A, V50, X52
- RF tuning step
- 25 kHz, varies by region
- Working range
- 100 m (330 ft); depends on RF conditions
- Diversity
- Digital predictive switching diversity
- Antenna bias voltage
- 12 to 13 V DC, 170 mA maximum per antenna
Audio
- Gain adjustment range
- -18 to +42 dB in 1 dB steps, plus Mute
- Audio outputs
- XLR balanced, mic/line switchable (30 dB pad); 1/4" (6.35 mm) impedance balanced
- Latency
- < 2.9 ms
- Dynamic range
- > 120 dB XLR analog (A-weighted, system gain +10)
Control & network
- Network interface
- Single-port Ethernet 10/100 Mbps; DHCP or manual IP; no Dante output
- Third-party control
- AMX/Crestron control over Ethernet TCP/IP, port 2202
- Encryption
- AES-256
Physical
- Dimensions and weight
- 42 x 197 x 171 mm (H x W x D); 913 g without antennas
- Power
- 15 V DC at 0.6 A from an external supply
Specifications from the manufacturer. Check the product page for the current details.
Connection
Connecting the Shure ULXD4 single-channel receiver
- Control protocol
- Shure network control over TCP/IP on port 2202, through the Showcaller Bridge App. No username or password.
- What Showcaller needs
- The receiver's IP address, shown on the front panel in the Network menu, and the model ULXD4 (Single Channel).
- Network
- Connect the receiver's Ethernet port to the same network as the Bridge App.
- Firmware
- Showcaller reads the receiver's firmware version when it connects. On newer firmware, third-party network control may need to be switched on in Wireless Workbench or the receiver's web interface.
- First check
- Showcaller reads the firmware version to check it can reach the receiver, then reads the channel status.
Tool Functions
Everything Showcaller can do with Shure Wireless
The Shure ULXD4 single-channel receiver uses the Shure Wireless integration. Each group shows the plan it is included from.
FAQ
Questions about the Shure ULXD4 single-channel receiver
Can Showcaller mute a Shure ULXD4?
Yes, in every plan. Showcaller mutes and unmutes the audio output without dropping the RF link, and reads the mute state. Shure notes that a power cycle unmutes the output. Remote mute works on ULX-D receivers only, not on QLX-D or SLX-D.
Does Showcaller read runtime with AA batteries?
No. With AA batteries it reads the battery bars. Runtime in minutes, charge and health come with Shure rechargeable batteries.
Does the ULXD4 have Dante?
No. Shure lists the Dante digital output on the ULXD4D and ULXD4Q only. The ULXD4 has XLR and 1/4" analog outputs and one Ethernet port for control.
What is the difference between the ULXD4, ULXD4D and ULXD4Q in Showcaller?
The Tool Functions are the same on all ULX-D receivers. The ULXD4 has one channel, the ULXD4D two and the ULXD4Q four. Pick the matching model when you connect.
Can Showcaller lock a ULX-D transmitter?
No. Showcaller does not lock or unlock bodypacks or handhelds. Lock the transmitter on the transmitter itself.
Same integration
Other Shure Wireless models
QLXD4 (Single Channel)Model page
SLXD4 (Single Channel)Model page
SLXD4D (Dual Channel)Model page
ULXD4D (Dual Channel)Model page
ULXD4Q (Quad Channel)Model page


